Gingelom · up to an hour's drive

On-site welding & machine repair

Werkhuizen Beckers comes to you with a fully equipped service van. Welding in steel, stainless steel and aluminium, and machines running again, mechanically and electrically.

Or directly +32 456 16 40 51 info@werkhuizenbeckers.be

  1. On site

    No dismantling, no transport to a workshop. The machine stays where it is.

  2. Everything in one job

    Welding, mechanics, machine electrics, pneumatics, hydraulics and controls. You call one number, not three companies.

  3. Quick to deploy

    Also when a machine is down and has to run again urgently.

  4. Engineering in-house

    Every repair is looked at through an engineer's eyes: why did it break, and how do you stop it happening again.

Services

Weld, repair, design

01

On-site welding

Repairing, reinforcing and modifying parts where they are: cracks, broken parts, brackets, frames and one-off pieces. Worn parts get a new wear layer. The service van is equipped for all welding work on site.

  • Steel, stainless steel and aluminium
  • Cast iron, with preheating and controlled cooling
  • Stick (MMA), MIG/MAG and TIG
  • Hardfacing and build-up welding: teeth, knives, blades, rollers, shafts and bearing seats
  • Drilling out broken bolts and repairing threads
  • Fabrication and custom work by arrangement

02

Repair and maintenance

Repairs to steelwork, machines and installations: mechanical, electrical, pneumatic, hydraulic and steam. Often with welding involved, but not always. Planned preventive maintenance, or tracking down and fixing a fault when the machine stops.

  • Bearings, shafts, drives and guides
  • Machine motors, sensors and control cabinets
  • Cylinders, valves, hoses and hydraulic lines
  • Steam systems: lines, valves, steam traps and supports

Electrical work on machines only, no building installations. Welding on steam lines by arrangement.

03

Bringing a machine back after a crash

Hit, tipped over or badly damaged. Broken parts are welded, the mechanics realigned, the electrical, pneumatic and hydraulic side repaired, and the machine set up again until it is back in production. Where needed, outdated parts or controls are replaced or upgraded.

Welding, mechanics, electrics and controls in one job.

04

Engineering, controls and robots

Design and drawings in Autodesk Inventor: modifications, reinforcements, brackets, guards and replacement parts. As part of a repair or as a separate job. Also changes to machine control systems and robot programs.

  • CAD design and workshop drawings (Autodesk Inventor)
  • Measuring and redrawing worn or broken parts
  • PLC and machine control changes
  • Robot program changes: KUKA, ABB and FANUC
  • Repairing robot cells, grippers and fixtures

05

Urgent call-outs

For breakdowns and breakages, especially when welding is needed. Urgent call-outs are first and foremost for regular customers. Other requests depend on availability.

Machine down?

Urgent

Machine down?

For regular customers, Werkhuizen Beckers is also on hand for urgent breakdowns. New customer? Feel free to call and see what is possible.

Call+32 456 16 40 51

Process

How it works

  1. 1

    Send a photo or call

    A photo by WhatsApp or email often says more than a long explanation. Mention where the machine is.

  2. 2

    Assessment

    What needs repairing, and which equipment goes along? That is settled before anyone sets off.

  3. 3

    Repair on site

    With the service van and the right tools. The machine stays where it is.

  4. 4

    Invoice, done

    You get an invoice listing the work. The machine is running again.

Service area

Based in Gingelom

Gingelom sits where Limburg, Flemish Brabant and the province of Liège meet. Within about an hour's drive: all of Limburg, the Campine and Hesbaye, Leuven and the eastern edge of Brussels, Mechelen, Liège, Verviers and Namur.

  • Limburg
  • Hesbaye (Haspengouw)
  • Campine (Kempen)
  • Flemish Brabant
  • Eastern Brussels
  • Walloon Brabant
  • Province of Liège
  • Province of Namur
  • Further afield by arrangement
Schematic map with Gingelom in the centre. Within 30 km: Sint-Truiden, Hasselt, Tienen, Tongeren, Diest and Huy. Within 60 km, about an hour's drive: Lommel, Geel, Mechelen, Brussels, Leuven, Wavre, Gembloux, Namur, Dinant, Liège, Verviers, Spa, Lier, Bree, Fleurus, Durbuy, Genk and Maasmechelen. 60 km · ± 1 hr 30 km Sint-Truiden Hasselt Genk Maasmechelen Lommel Geel Diest Mechelen Brussels Leuven Tienen Tongeren Wavre Gembloux Namur Dinant Huy Liège Verviers Spa Lier Bree Fleurus Durbuy Gingelom N
Schematic, straight-line distances. Outer circle: about an hour's drive.
Lander Beckers, managing director

About

Lander Beckers

I run Werkhuizen Beckers and I am an engineer by training. Even so, I choose to work hands-on: welding, fixing and troubleshooting happen at the machine, not behind a desk.

That background helps when a repair takes more than a weld. The question is not just where something broke, but why.

At Werkhuizen Beckers you can be helped in English, Dutch and German.

Certificates and insurance

  • VCA VOL safety certificate
  • BA4 and BA5 electrical qualifications
  • Forklift certificate
  • Insured: public and professional liability

FAQ

Frequently asked questions

Do you work outside Limburg?

Yes. Up to about an hour's drive from Gingelom: Hesbaye, Leuven, the eastern edge of Brussels, Mechelen, Liège, Verviers and Namur. Further afield is possible by arrangement.

Does the machine need to be dismantled?

Usually not. Welding and repairs are done where the machine stands. If a part has to come off to reach the damage, that is done on site.

Which materials do you weld?

Steel, stainless steel, aluminium and cast iron. Stick (MMA), MIG/MAG or TIG, depending on the job and the location. Worn parts can also be hardfaced.

Do you do electrical work too?

On machines only: motors, sensors, control cabinets and the wiring on the machine. Building electrics are not included.

Can you just make a drawing or a design?

Yes. CAD design and workshop drawings in Autodesk Inventor are also available as a separate job, for example for a modification, a bracket or a replacement part you have made elsewhere.

Do you also change robot programs?

Yes, for KUKA, ABB and FANUC. For example after a repair or a change to the cell, when positions or paths have to be set again.

How do I send a photo of the problem?

Through WhatsApp to +32 456 16 40 51 or by email to info@werkhuizenbeckers.be. Add the location and a short description.

Contact

Call, email or send a photo

Pick whatever is easiest for you. Prefer to write? Fill in the form and you will get a call or an email back.

Gingelom – Sint-Truiden

Describe the problem

Photos are easiest to send through WhatsApp or by email.

Phone or email, one of the two is enough.

For example: cracked bracket on a conveyor, worn knives on a forage harvester, hydraulic leak on a press.